How To: Behringer ADA8000 Into Digi 002/003 - TheRecordingRevolution.com descargar videos gratis

onesufi

Can tell me how I would connect to SSL Vh1 pre to UA Apollo silver, using adat in Logic. I thought Apollo has to be the master. Thanks

producer_fuji

Question if I use the digi 003and connect the optical in and to focusrite 56 will 5th at give me extra outputs and inputs or vise verses ? ???????

HitMen Production Group

Hey Graham can I slave the AD8000 from my Apogee converters then slave the 002 last in the chain? Apogee->AD8000->002?

Michal N Wysokinski

Helo Mr. is it possibile to use two channels from Behringer ADA8200 Ultragain as a monitors outputs ?

benshke

HiJust a quick question, are you able off connecting more than 1 behringer unit connecting it with in/ou/in/out so you get 16 or more inputs?

Isaias AES

Please, I have an ADA 8000 and I want to record with my digi 002 how should I leave ampos configured for good communication? If pider help me thank you

Anthony Ayora

I want to buy an ADA8200... Is it a good rack or I must save money and buy presonus digimax d8?

Rob Scott

Could i use an external clock like a "big ben" as the master and hook it to the ada (ada now set to slave) using BNC cable then run it through digi 002 via lightpipe and keep the same settings in PT??

riki rex

So that would be the trick to interface my digital 32 tks recorder digit out in to my lap top...?

Alekz T.

So, does that mean I don't need the word clock conection? I trying to synchronise my scalett 18i20 with my focusrite octopre dynamic. help please! I have to record a live band on April first.

MegaCrasherMusic

A couple of questions:Is each of the 8 ADAT channels stereo or mono?I see you slaved your audio interface to the ADAT preamp -- wouldn't it normally be the other way around?Somewhat unrelated but have always wondered… is it OK to install rackmount devices right on top of one another in the rack? I always thought you were supposed to leave open space between units for ventilation

Killian Playthell Steele

Thank you for making this simple. I am not familiar with digital recording I'm old school and trying to get someone who knows about adding an interface using ADAt has been tricky.

Mauro Cappabianca

Old but gold.. I was thinking about buying a new audio interface and thanks to this video you made my decision a lot easier!! Thanks Graham you're fantastic

simone molla

do you know if it's possible to use ada8000 with digi002 in stand alone mode?I know this is possible by digidesign manual passing through ch.5-6 but i don't get any signal by it.Can you also explain the difference between setting the ADA as a slave or master ADAT in?

Trey Nobles

So does that mean that if I connect this to a small interface as long as it has the ADAT in and it will turn that interface from 2 channels to 10 channels basically?

Fyba Glass Music

Hey Graham, how do I connect a Apogee Rosetta 800 to a digi 003 and a Avalon vt 737 Compressor via a beringer patch bay and get everything to work in Pro tools?

12ealDeal

I got an ADA8000 based on the word of a few of my favorite recording gurus. At $39 it seemed like a steal. Once I put the thing into my rack and connected it via optical to my Pro40, the thing sounded like hot garbage. It didn't occur to me that the Behringer's clock would be the one my interface needed to sync to, but I only had a hunch that a sampling issue was taking place because the audio almost sounded bit crushed. I'm glad I saw this because I was going to have to call up the retailer and fight for the cost of the shipping to be reimbursed.

Mirko Burroni

if i weanna use my umc1820 as master and umc8200 as slave on the back of the 8200 on the sync section i slide all the way to the left where it says slave?

Daniel Hopkins

I want to connect my Mackie Onyx 24.4 control surface to my Alesis 3632 Compressor and mic preamp. anyway to make that happen?

rolasmusic

I have Digidesing 002 Mixer and I connect the behringer ADA8000 with the optical cable. And I can't get working ??? I choose the optical clock on hardware what I doing wrong. ???